| Price | Negotiatable |
| MOQ | 1 set |
| Delivery Time | 45days |
| Brand | HongCe |
| Place of Origin | China |
| Certification | calibration certificate (cost additional) |
| Model Number | HK1503 |
| Packaging Details | plywood |
| Payment Terms | T/T |
| Supply Ability | 10 set /month |
| Test sample | Self Ballast Lamp(SBL) Switches | Input voltage | Adjustable |
| Place of Origin | China | Packaging Details | plywood |
| Power meter | 0~9KW | Model Number | HK1503 |
| Supply Ability | 10 set /month | Certification | calibration certificate (cost additional) |
| Brand Name | HongCe | Payment Terms | T/T |
| Protection time | 1~99S | Stations | 3 stations |
| Rated current | 10,13,16,20A optional | Voltage meter | 0 ~ 300V |
| Price | Negotiatable | Delivery Time | 45days |
| Minimum Order Quantity | 1 set | Preset rated voltage | 250V |
IEC60669-1 Clause 19.3 Self Ballasted Lamp Load Box SBL Switch Tester 250V
Switches
intended
for
self
ballasted
lamp
(SBL)
loads
shall
withstand,
without
excessive
wear
or
other
harmful
effect,
the
electrical
and
thermal
stresses
occurring
when
controlling
self
ballasted
lamp
circuits.
Compliance
is
checked
by
connecting
the
load
as
given
in
Figure
12b
via
the
switch
under
test
to
a
power
supply.
The
calculations
are
based
on
the
following
parameters
in
order
to
have
the
required
values
for
inrush
current
and
I
2
t:
–
a
prospective
short-circuit
current
(rms)
of
the
supply
of
3
kA
at
cos
ϕ
=
0,9
(lagging);
–
a
resistance
R
3
equal
to
0,25
Ω
in
the
test
circuit
to
the
load.
This
value
is
obtained
with
a
wire
having
a
cross-sectional
area
of
1,5
mm
2
when
switches
with
rated
current
up
to
and
including
13
A
are
being
tested
and
2,5
mm
2
when
switches
with
rated
current
over
13
A
up
to
and
including
20
A
are
being
tested.
Standard: IEC60669-1:2017 clause 19.3
Application: This device is suitable for breaking capacity and normal operation life test to fixed switches for house held and similar purpose, especially suitable for self ballast lamp switch electric stress and thermal stress test when control the LED circuit. To verify whether the switch can withstand normal use, any mechanical damage or electrical fatigue failure under normal operation, any contact adhesion phenomenon or long term closure or disconnection phenomenon, to test whether excessive wear or other harmful consequences.
Test sample: Self Ballast Lamp(SBL) Switches
Feature: Dimension about: wide (800mm) * Deep (800mm) * high (1800mm). The frame is blue and the side panels are light white. Above the front is the operation control panel. On the control there are power switch, product test voltage and power display instruments, alarms, touch screen, etc., there are resistors and capacitor load combinations, AC contactors, relays. There is a terminal under the box, which is connected to the product in the testing machine through the wire, and outputs current and provides load in the inspection process.
The load device has been preset with standard load conditions before shipment. As long as the test voltage is adjusted to 250V~, the operator presses the switch button with the same rated current as the switch to be tested, and its rated power, impulse waveform, Ipeak and I2t meet the corresponding requirements of the standard.
There are 3 stations and 3 switches can be tested at the same time.
With metering mode and metering dedicated port, built-in 90-degree closing plate, easy to measure the output waveform, Ipeak current value and I2t energy value, fully meet the standards for equipment measurement requirements.
The device is equipped with a voltage regulator, which can reach the voltage of 250V required by the switch test without the need of an external voltage regulator.
Parameters:
| NO. | Item | Parameter |
| 1 | Power supply | single phase AC220V±5%/50Hz |
| 2 | Voltage meter | 0 ~ 300V, precision 0.5, digital display |
| 3 | Power meter | 0~9KW, precision 0.5, digital display |
| 4 | Output channel | 3 |
| 5 | preset switch rated voltage | 250V |
| 6 | rated current | 0A, 13A, 16A, 20A optional (can be customized test voltage and Test current) |
| 7 | input voltage | Adjustable, to ensure that the test voltage is 250V |
| 8 | All operating parameters are set at 250V~, including W, Ipeak, I2t, and inrush current waveforms | |
| 9 | Each device provides a closing control device (touch screen select "measurement" function),each time is in the 90 degree angle conduction, this function can be used for initial equipment calibration and measurement verification. | |
| 10 | With long / long protection function, the protection time of 1 ~ 99S can be preset, shutdown alarm protection. | |
| 11 |
Use environment: temperature 5 ~ 40 °C, relative humidity 20 ~ 90% RH, atmospheric pressure 80 ~ 106kpa. No severe vibration, no electromagnetic interference, no dust, corrosive gas, good heat dissipation.
|
|
Picture for reference:
